How to Disassemble the IQOS Device

IQOS Maintenance - How to Safely Disassemble Your Device

Disassembling your IQOS device may seem like a daunting task at first, but don’t worry - we’ve got you covered. To ensure you get the most out of your IQOS experience, let’s walk through how to safely and effectively disassemble your device.

• First, you’ll want to make sure that the IQOS is turned off and cooled down before attempting any maintenance.
• Then, use a flathead screwdriver to carefully remove the screws on the base of the device.
• Once you’ve removed the screws, gently pull the body of your device away from the base.
• Then, unscrew the three screws that hold together the interior heating system and carefully remove the interior components.

As a reminder, it’s important to be gentle when disassembling your IQOS device and handle it with care. If you have any further questions, contact your local IQOS store for assistance.

The Ultimate IQOS Disassembly Tutorial

So you thought it would be a good idea to try breaking down your IQOS device? No worries, we’ve got your back! We’ll walk you through the steps of disassembling your device so that you can get to all those hard-to-reach places. Let’s get started!

• First and foremost, make sure you have the right tools on hand – a small screwdriver or tweezers should do the trick.
• Next, carefully remove the back cover of the device to access its internal components. Now you can unscrew the screws and lift the mainboard out of the device.
• From there, it’s time to take out all the bits and pieces. Unscrew the screws from the side and carefully remove each component from its slot.
• Be sure to keep track of which parts belong in which slots, so you can easily put them back in place once the disassembly is complete.
• Once you’ve got all the pieces out, it’s time to get access to the inner workings of the device. To do this, you must unclip and remove the two circuit boards.
• With the circuit boards out of the way, you can now access the internal components of your device, like the battery and other removable pieces.
• Finally, reassemble your device by placing all the components back in their respective slots and screws.

Once you’ve got everything back together, you’re ready to start using your newly disassembled IQOS device again!

Why Disassemble IQOS?

It is important to disassemble your IQOS device in these conditions

• If you drop by mistake your IQOS device in the water
• When IQOS does not heat stick properly
• Like some time battery not working and need to replace
• When something breaks from inside
• When the heat button not works

Are you tired of your IQOS not performing as expected? Not producing enough vapor? Or maybe it’s just too hard to clean… seems like a daunting task, doesn't it? Enter disassembly time! Taking apart your IQOS device can help you diagnose any issues and give you the opportunity to clean it thoroughly. Plus learning how to take apart and put back together something as sophisticated as an IQOS device can be quite satisfying.

What tools are required to disassemble IQOS?

Well, if you're looking to take apart your IQOS device, the good news is that you don't need any special tools. All you need is a bit of know-how and some elbow grease to get the job done.

• A tweezer of small size
• A slender sheet of metal
• Blade or something small or sharp
• Screwdriver
• And of course, some patience!

If you do find yourself in a sticky situation, don’t worry. You can always call upon the pros at IQOS to help you out. With their expertise, they can make sure that your device is disassembled properly and safely.

Learn the Simple Steps of disassembling IQOS 2.4 Holder

Ready to take your IQOS 2.4 Holder apart? Let's start! Before we begin, make sure you have the proper tools on hand. You'll need a Phillips screwdriver, tweezers, and a flat-head driver. Let's get started disassembling step by step.

• Begin by removing the battery by pressing the release button on the bottom of the device.
• Use a small Phillips-head screwdriver to remove the screws on the back of the device.
• Carefully separate the back cover from the rest of the device.
• Remove the circuit board and any other components that are attached to it.
• Use a pair of tweezers to carefully detach any connectors or cables that are still connected to the circuit board.
• Once all components have been removed, you can clean and inspect each piece individually.
• Reassemble the device in the reverse order of disassembly.

The disassembly process is complete. To reassemble, start by inserting the electronic board, battery, and blade into the holder from the bottom. The heater should be positioned facing forward. Be careful not to force any parts into place as they may not properly align. Pay attention to the latches and ensure they are securely in place before fully reassembling the device.

When reassembling the IQOS 2.4, it is crucial to handle the heating rod (blade) with care, as it is delicate and can easily break. When putting the device back together, avoid using excessive force and make sure to properly install the bracket. Once that is done, carefully place the top part of the case back on and insert the ring, then attach the button. Next, securely fasten the bottom of the case. Once all the components are in place, your IQOS 2.4 should be fully functional and ready for use.

Disassembling the IQOS 2.4 requires extra caution, as some of the newer models may be glued together. The metal tube inside can be taken out by soaking it in isopropyl alcohol to dissolve any adhesive. However, one must always practice fire safety when handling solvents - so make sure you are working in a room with no open flames and proper ventilation for combustible fumes!

Once you're done, your IQOS 2.4 Holder should be ready for use again! With this simple guide, disassembling and reassembling your device is easy. Now you can start using it again and enjoy the convenience of smoking real tobacco without fire. Enjoy!

Dismantling the Charger for Maintenance and Repairs

Next up, we'll learn how to disassemble the IQOS charger. This is a necessary step if you want to replace the battery or clean the device. Let's discuss this step by step.

• Begin by unplugging the charger from the power source.
• Use a small Phillips-head screwdriver to remove the screws on the bottom of the charger.
• Carefully separate the bottom cover from the rest of the charger.
• Carefully remove the circuit board and any other components that are attached to it.
• Use a pair of tweezers to carefully detach any connectors or cables that are still connected to the circuit board.
• Once all components have been removed, you can clean and inspect each piece individually.
• Reassemble the charger in the reverse order of disassembly.
• Make sure to keep the screws in a safe place, so you don't lose them.

It is important to note that the IQOS 2.4 charger is not user-serviceable and opening it or modifying it can damage it, void the warranty, and could be dangerous. The best practice is to take it to an authorized IQOS Service Center for maintenance or repair.

Now that you know how to disassemble the IQOS 2.4, you can keep it in good working condition with proper cleaning and maintenance. Taking care of your device will ensure it works effectively and safely, allowing you to enjoy the convenience of smoking real tobacco without fire for longer.

Learn the Simple Steps of disassembling IQOS 3 DUOS Holder

If you want to try disassembling the IQOS 3 DUOS holder with a repair kit, here are some simple steps to follow:

• Turn off the device and ensure it is cooled down before disassembling.
• Remove the holder from the device by pressing the release button and sliding it out.
• Unscrew the battery compartment at the bottom of the device to remove the battery.
• Carefully remove the charging port cover located on the side of the device.
• Gently remove the heating blade from the device by pulling it out from the top.
• If necessary, remove the cleaner tool by pulling it out from the bottom of the device.
• Before reassembling, ensure all parts are clean and free of debris.
• Reassemble the device in reverse order, making sure all parts are securely in place.
• Turn on the device and test for proper function before using it.

Finally, turn on the device and test for proper function before using it again. By following these steps carefully you will be able to safely disassemble your IQOS 3 DUOS without damaging any components or voiding warranties.

During any repair work, it is essential to remember not to overlook reconnecting pins that had been disconnected! Now you have the knowledge to disassemble the IQOS 3 DUOS holder! If you're still feeling stuck, feel free to reach out to a professional for assistance. It’s always better to be safe than sorry.

Disassembling the Charger for Maintenance and Repairs

If you need to take apart your IQOS 3 DUOS charger for either maintenance or repairs, here’s what you’ll need to do. Follow these simple steps.

• Turn off the device and disconnect it from the charger.
• To avoid potential damage to the micro switch on the board, please only carry out any modifications or maintenance while the case cover is open.
• Carefully unscrew the screws located on either side of the charging stand.
• Once the screws are out, you can then remove the top section of your charging stand from the bottom half.
• Remove and unscrew the battery and PCB from the inside.
• Unscrew the four screws on the inside of the power board to disconnect it from the charger.
• If soldering is one of your skills, then you can confidently remove the electronic board. Go ahead and take out that component with confidence!
• Then, loosen the bolt that attaches the magnetic cable to its base.
• Now your IQOS 3 DUOS charger is ready for maintenance and repairs! Just make sure to put it back together correctly.

Assembling a dismantled device into a magnet is usually difficult due to its fragility, especially the soldering, cleaning, and conversion tasks. Remarkably enough though, deconstruction of this process can be accomplished in reverse order:

• Sliding the magnet into position, firmly tighten the bolt at its base until you hear a click.
• Place the board and join it to the various cables including magnetic, indicator, and battery ones respectively.
• Make sure that everything is working properly by testing if an indication appears or not when turned on.
• Securely fix in place your plastic cover of the board with a screw for extra reinforcement if necessary.
• Now insert firstly upper groove side of the inner part into the body before fixing the bottom hole's screw then fully inserting the entire component within the case via a twist-in motion from said screw holes.
• Lastly, fasten up the topmost area's screws tightly, and your charger is all ready to power up again!

And that's all there is to it. You’re now free to maintain and repair your IQOS 3 DUOS like a pro! With these easy steps, you can take apart and put together your device with confidence - no need to worry about any broken parts or voiding warranties. So relax and have a go at fixing up your device today! Good luck.

Restoring and Substituting Heating Components

Please be aware that attempting to repair or modify an IQOS device may void its warranty and could be a safety hazard. That being said, the following is a more detailed and organized guide for the replacement of the heating element of an IQOS device.

• Gather the necessary tools: a soldering iron, flux, and a flat nail file (if needed)
• Disassemble the device according to the manufacturer's instructions.
• Carefully remove the adhesive from the pins that connect the plastic base of the blade to the device.
• Use the soldering iron and flux to detach the wire that fixes the contacts. Then, gently remove the base from the board.
• Clean the hole for the blade if necessary, and use the flat nail file to widen it if needed.
• Carefully insert the new heating element. Ensure it's properly seated but do not force it.
• Replace the base with the new blade and use the soldering iron and flux to reattach the contacts.
• Reassemble the device according to the manufacturer's instructions and test it to ensure it's working properly.

It is important to note that this is a general guide and it's important to consult the manufacturer's instructions or contact IQOS customer service for guidance.

How to Fix IQOS LID - Step by Step

If your IQOS 2.4 or 2.4 Plus device's lid is not closing properly, it may be due to a broken latch or tongue, located above the button in the groove. To fix this issue, purchase the missing part from an official IQOS boutique or online retailer such as Aliexpress. To replace the latch:

• Remove the housing according to the device manual.
• Carefully pry off the cover using a thin plastic tool and press the button with a skewer or similar tool.
• Remove the cover and button, being mindful of the fragile plastic.
• Clean the surface of the latch with a degreaser.
• Apply glue to hard plastic and place the new part on it.
• Allow the product to dry and gently sand it with sandpaper or a file.

Assemble the device in reverse order, placing the top cover and body back together. To replace the button, simply insert the new part in place of the old one. For better clarity, we recommend watching a video instruction.

Revitalize your device with a fresh battery replacement.

Replacing the battery of the IQOS 2.4 case is a simple task that can be accomplished with a new battery and a thin tool such as a plastic card or metal pick.

To begin, follow these steps:

• Disassemble the case by unplugging the cable from the board and carefully removing the old battery from the socket.
• Insert the new battery making sure the notch is facing the right direction.
• Reassemble the device by reconnecting the cable and ensuring that the rubber dampers for the board are in place.
• Test the device to make sure that it turns on and functions properly. Once you are finished, your device will be ready for use.

If you want to replace the battery holder, gently pull the inside out of the metal tube. This process can also be applied to IQOS 3 and IQOS Duos. It is always a good idea to refer to the device's manual for detailed instructions and precautions before attempting to replace the battery.

If the case is glued, you can soften the glue by soaking it in isopropyl alcohol or solvent 646. Then carefully remove the battery along with the board, being mindful of the contact that connects them. The contact should be soldered or cut with a scalpel. Carefully remove the remaining old contact from the board, install the new battery and carefully solder the contact to the board.

In comparison to 2.4, the layout of this case is quite different.

To begin the process of disassembling your device, start by equipping yourself with a T5 screwdriver to unfasten the screws on both the case and board shroud. Now you’re ready for step one:

• Disassemble the case according to the instructions provided until you reach the point where you need to remove the plastic protection. Carefully remove the indication cable, the adhesive tape used to secure the battery, and the battery connector.
• Insert the new battery, making sure the notch falls into the upper groove located under the board.
• Connect the cable, secure it with tape and reattach the battery connector.
• Reinstall the transparent cover and reassemble the device in reverse order, ensuring that all screws are tightened securely.
• Test the device to make sure it is functioning properly.

It is always a good idea to refer to the device's manual for detailed instructions and precautions before attempting to replace the battery. You can also refer to online video tutorials for visual guidance. With a few simple steps, you can have your device up and running again in no time.